HARTELL Ice Machine Pumps

Fit commercial ice-making equipment to supply water & provide a continuous supply of ice. Can also reuse the discharged condensate from the ice-making equipment.

Filter

Hartell replacement ice machine pumps are designed to fit commercial ice-making equipment, such as Scotsman, Manitowoc, Ice-O-Matic, Cornelius / Ross Temp, Crystal Tips / McQuay, Whirlpool / Frigidaire and York.

HARTELL -

GPP Series Ice Machine Pumps

HARTELL GPP-3M-1SA
HARTELL GPP-1MH-1PB
HARTELL GPP-3S-1C
HARTELL GPP-3MH-1PD
HARTELL GPP-3MA-1E
HARTELL GPP-4MA-1F
HARTELL GPP-5MA-1G
HARTELL GPP-4S-1H
HARTELL GPP-3S-1BI
HARTELL GPP-8MA-2AJ
HARTELL GPP-6L-2BK
HARTELL GPP-3MH-2PL
HARTELL GPP-4S-2M
HARTELL GPP-3RC-4N
HARTELL GPP-9M-4O
HARTELL GPP-3S-2P
HARTELL GPP-5MA-2AQ
HARTELL GPP-4MH-2PR
StyleModelVoltageOutside Dia.FrequencyPrice (inc. GST)
AGPP-3M-1S115V3/4"60 HzA$ 329.28
RFQ
BGPP-1MH-1P115V5/8"50/60 HzA$ 234.59
RFQ
CGPP-3S-1115V1/2"60 HzA$ 310.05
RFQ
DGPP-3MH-1P115V5/8"60 HzA$ 230.37
RFQ
EGPP-3MA-1115V1"60 HzA$ 606.82
RFQ
FGPP-4MA-1115V1/2"60 HzA$ 310.40
RFQ
GGPP-5MA-1115V1/2"60 HzA$ 361.47
RFQ
HGPP-4S-1115V3/4"60 HzA$ 276.61
RFQ
IGPP-3S-1B115V3/4"60 HzA$ 305.22
RFQ
JGPP-8MA-2A230V1"50/60 HzA$ 289.09
RFQ
EGPP-3MA-2230V1"50/60 HzA$ 619.23
RFQ
KGPP-6L-2B230V5/8"50/60 HzA$ 303.33
RFQ
LGPP-3MH-2P230V5/8"50/60 HzA$ 242.75
RFQ
MGPP-4S-2230V3/4"50/60 HzA$ 237.12
RFQ
NGPP-3RC-4230V5/8"50/60 HzA$ 262.30
RFQ
OGPP-9M-4230V1"50/60 HzA$ 353.28
RFQ
PGPP-3S-2230V1/2"50/60 HzA$ 270.59
RFQ
QGPP-5MA-2A230V1/2"50/60 HzA$ 375.04
RFQ
RGPP-4MH-2P230V5/8"50/60 HzA$ 200.77
RFQ
BGPP-1MH-2P230V5/8"50/60 HzA$ 189.63
RFQ
KGPP-15Y-2230V1"50/60 HzA$ 386.75
RFQ

Features

  • Hartell ice machine pumps have a dual ball bearing system to provide high speeds and low friction.
  • They have a stainless steel shaft to prevent contamination and protect critical moving components.
  • These pumps feature a thermally protected motor to prevent overheating.

Frequently Asked Questions

How to install Hartell ice machine pumps?

  • Position and hold the motor with the shaft facing up.
  • Place one washer over each motor stud.
  • Slide the slinger down the motor shaft to about 1/2-inch from the motor.
  • Place bracket (if used) over motor studs.
  • Place the housing over motor studs and note the orientation of discharge.
  • Place one washer over each motor stud.
  • Screw the thumb nuts onto the motor studs. Do not tighten.
  • Center the motor shaft in the housing centre hole and tighten the thumb nuts.
  • Slide the impeller onto the motor shaft.
  • Push and hold down the impeller. Screw the impeller nut into the motor shaft until it touches the impeller.

We are here to help!

Looking for a part not listed here?

Chat with us now